Tachometer unit NOTE: Depending on the model of the outboard motor, some functions may not be compatible. For information on models which contain the compatible functions, consult a Yamaha dealer. Tachometer The tachometer shows the engine revolutions per minute. (Page 3) Trim meter The trim meter shows the trim angle of the outboard motor. Digital Gauges For those running F20 to XF425 outboards, Genuine Yamaha conventional digital gauges offer flexibility and streamlined rigging. They also provide the ability to monitor several vital boat systems, performance and trip stats when properly equipped. 6Y5 Multi-Function Tachometer. Re: Yamaha Tachometer Problem I have posted on this till I am blue in the face, the tach came out of the box set for 4 stroke,2 wire trim and 12 pole altenator, you have to set the switches for 2 stroke,the correct trim, and 12 pole altenator. 2001 was the break for 3 wire trim sender. Yours should be 2 wire but look at it, if it has only a pink and black its 2 wire. There are two gauges in the Yamaha Command Link Digital Gauge System—a tachometer unit and speedometer fuel unit—each with different functions and readouts. The gauges come with an Owner's Manual that helps walk you through their operations, and also explains how to set the initial settings on the gauges when you first get your boat.
Sections:
PREFACE
This flush mount, alternator tachometer is designed for use on the following:
Johnson® and Evinrude® Outboards
OMC Sea Drive® Models
NON-BRP products with 20 pole alternators
Installation
Disconnect battery cables to help prevent arcing or damage to equipment.
Select a tachometer mounting location that is in full view of the operator.
Drill a 3-3/8 in. (86mm) hole in the dashboard.
Mount the tachometer so water will not collect on the face, or drip on the case and wires. If the tachometer is covered by a transparent shield, the shield must be adequately ventilated to help prevent sunlight heat soak damage.
Set Pulse Selector Switch
[1]
Align the arrow on the PUL/REV (pulses-per-revolution) switch (A) with the appropriate number.
Engines with two yellow stator wires (yellow and yellow/gray) set switch to '6'
Engines with three yellow stator wires (yellow, yellow/gray and yellow/blue) set switch to '5'
NON-BRP engines with 20 pole charging system, set switch to '3' Power geez 2010 setup.
1968 THRU 1972 Outboards
If you are replacing an older Battery CD Ignition tachometer, or if the engine has never had a tachometer, move the engine harness gray wire to the rectifier yellow/gray circuit on the terminal board.
1978 and Newer Outboard and OMC Sea Drive
Use a wiring kit to connect the tachometer to the plug-in connector on the remote control or accessory electrical cable.
Use Plug-In Connector Kit P/N 0174732 when installing tachometer only.
Use Plug-In/Fuse Block Kit P/N 0173611 when installing tachometer with other accessories. Zion y lennox age.
All Models
Use No. 8 insulated ring terminals and No. 16 A.W.G. wire of the specified color.
[1]
HELPFUL HINT: install star washer, ring terminal, and nut - in that order. This will help prevent ring terminal from rotating and loosening the nut. Connect all wires before installing gauge in dashboard.
[1]
Connect the following:
(B) To dashboard light switch, DARK BLUE WIRE.
(C) To alternator, GRAY WIRE.
(D) To ground connection, BLACK WIRE.
(E) To key switch accessory terminal, PURPLE WIRE.
Insert the gauge into dashboard. Install bracket, star washers, and mounting nuts.
Do not overtighten the mounting nuts as you could permanently damage the gauge.
Connect battery cables. Test the tachometer operation by running the engine.
Important: Multiple battery installations require a common battery ground cable. Refer to Outboard Installation Guidelines P/N 0508167.
[1]
To replace the light bulb, pry out light socket cover (F). Turn bulb socket counter-clockwise and pull out. Replace with a No. 194 bulb, P/N 0125432.
Variety of yamaha outboard tachometer wiring diagram. A wiring diagram is a simplified standard photographic representation of an electric circuit. It reveals the elements of the circuit as simplified forms, as well as the power and signal connections in between the tools.
A wiring diagram typically provides details about the loved one setting as well as arrangement of gadgets and also terminals on the tools, in order to help in structure or servicing the gadget. This differs a schematic representation, where the setup of the elements' interconnections on the representation generally does not match to the elements' physical locations in the ended up device. A pictorial diagram would certainly reveal more detail of the physical look, whereas a wiring diagram makes use of an extra symbolic symbols to stress affiliations over physical appearance.
A wiring diagram is frequently utilized to fix problems as well as to make sure that the connections have been made which whatever exists.
yamaha outboard tachometer wiring diagram
All Models
Use No. 8 insulated ring terminals and No. 16 A.W.G. wire of the specified color.
[1]
HELPFUL HINT: install star washer, ring terminal, and nut - in that order. This will help prevent ring terminal from rotating and loosening the nut. Connect all wires before installing gauge in dashboard.
[1]
Connect the following:
(B) To dashboard light switch, DARK BLUE WIRE.
(C) To alternator, GRAY WIRE.
(D) To ground connection, BLACK WIRE.
(E) To key switch accessory terminal, PURPLE WIRE.
Insert the gauge into dashboard. Install bracket, star washers, and mounting nuts.
Do not overtighten the mounting nuts as you could permanently damage the gauge.
Connect battery cables. Test the tachometer operation by running the engine.
Important: Multiple battery installations require a common battery ground cable. Refer to Outboard Installation Guidelines P/N 0508167.
[1]
To replace the light bulb, pry out light socket cover (F). Turn bulb socket counter-clockwise and pull out. Replace with a No. 194 bulb, P/N 0125432.
Variety of yamaha outboard tachometer wiring diagram. A wiring diagram is a simplified standard photographic representation of an electric circuit. It reveals the elements of the circuit as simplified forms, as well as the power and signal connections in between the tools.
A wiring diagram typically provides details about the loved one setting as well as arrangement of gadgets and also terminals on the tools, in order to help in structure or servicing the gadget. This differs a schematic representation, where the setup of the elements' interconnections on the representation generally does not match to the elements' physical locations in the ended up device. A pictorial diagram would certainly reveal more detail of the physical look, whereas a wiring diagram makes use of an extra symbolic symbols to stress affiliations over physical appearance.
A wiring diagram is frequently utilized to fix problems as well as to make sure that the connections have been made which whatever exists.
yamaha outboard tachometer wiring diagram
Wiring Diagram Pics Detail:
- Name: yamaha outboard tachometer wiring diagram – mercury outboard wiring diagrams mastertech marin rh maxrules 50 HP Mercury Outboard Wiring Diagram Mercury Outboard Wiring Schematic Diagram
- File Type: JPG
- Source: veturecapitaltrust.co
- Size: 332.19 KB
- Dimension: 1200 x 1655
Wiring Diagram Images Detail:
- Name: yamaha outboard tachometer wiring diagram – Yamaha Fuel Gauge Wiring Wiring Diagram • Yamaha Outboard Wiring Diagram
- File Type: JPG
- Source: galericanna.com
- Size: 212.57 KB
- Dimension: 2050 x 1193
Yamaha Outboard Multifunction Gauge Manual
Collection of yamaha outboard tachometer wiring diagram. Click on the image to enlarge, and then save it to your computer by right clicking on the image.
A Beginner s Overview to Circuit Diagrams
A first appearance at a circuit layout may be complicated, however if you could read a train map, you could read schematics. The objective is the exact same: getting from point A to point B. Literally, a circuit is the course that allows power to flow.
The Language of Circuitry
Let s look at some of terms that you will need to understand:
Voltage: Gauged in volts (V), voltage is the pressure or pressure of electrical power. This is generally provided by a battery (such as a 9V battery) or keys electrical energy, the outlets in your house run at 120V. Electrical outlets in various other countries run at a various voltage, which is why you need a converter when traveling.
Existing: Existing is the circulation of electricity, or more specifically, the circulation of electrons. It is measured in Amperes (Amps), as well as can just move when a voltage supply is attached.
Resistance: Gauged in Ohms (R or O), resistance defines just how quickly electrons could flow with a material. Products such as gold or copper, are called conductors, as they easily permit circulation of movement (reduced resistance). Plastic, timber, as well as air are examples of insulators, preventing the motion of electrons (high resistance).
DC (Direct Current). DC is a continuous flow of existing in one instructions. DC can flow not just with conductors, but semi-conductors, insulators, and also a vacuum cleaner.
AC (Rotating Existing). In Air Conditioning, the flow of existing regularly rotates in between two instructions, commonly forming a sine wave. The frequency of Air Conditioning is determined in Hertz (Hz), as well as is generally 60 Hz for electrical energy in property and also organisation purposes.
The Schematics
Finishing an electric engineering level as well as after that getting a work in the field implies you will see a great deal a whole lot a whole lot of these schematics. It s vital to recognize precisely just what is going on with these.
Yamaha Outboard Tachometer Gauge
Starting to make good sense? These are the fundamentals and also may even seem apparent or intuitive to you, such as the cables as well as if they are linked. Whenever you establish your particular area of electric design, you may see extra complex representations as well as signs. You ll learn additionally that different nations use various signs. As an example, of both icons for resistors over, the very first one is utilized in the UNITED STATE, while the second is made use of in Europe. You will certainly likewise discover about the various symbols utilized for buttons, various other power supplies, inductors, meters, lights, LEDs, transistors, antennas, and also a lot more.
